M4x/5x/60 Speeduino Compatible PNP Kit
Note: Please allow a lead time of 1-2 weeks to assemble and test these boards. Enclosures are provided while stocks last. Please let us know if you don’t require one.
For newcomers to the world of Speeduino, it can be a challenge to navigate through the in-depth information contained within the forums, let alone sourcing the correct componentry from the scattered array of part suppliers.
So let us do the hard work for you!
These boards are designed to fit into your factory ECU/DME housing, to make for a clean install using the car’s factory engine harness.
Currently, this kit can be made to suit the following BMW Motors:
M40 (E36 Era)
M42
M43
M50NV
M50TU
M60
This kit is capable of:
6-cylinder sequential injection/ignition (with firmware modification)
Launch Control
Accepts boost solenoid output
Wideband input
Flex fuel input
3 spare relay outputs
3 spare analog/digital inputs for additional sensors
To install the kit, you will need to open up the ECU in your car and remove the original circuit board and replace with this kit.
Additionally, you will need to drill/dremel out openings for the rear I/O of the ECU to cover the MAP (optional) sensor input, the 16 pin expansion plug (optional) and Arduino USB Input (mandatory)
If you are unsure or have queries about this item, please contact us before ordering.
*Extra Components included:
x1 VR Conditioner
Extras
We also offer a core exchange service at an additional charge.
You simply ship us your ECU and we will take care of the entire re-fit for you and once done, we send you back the newly fitted-out ECU, as well as the original components, ready to go!
NB: This circuit board is designed by Pazi88 and all credit goes to them.
Note: Please allow a lead time of 1-2 weeks to assemble and test these boards. Enclosures are provided while stocks last. Please let us know if you don’t require one.
For newcomers to the world of Speeduino, it can be a challenge to navigate through the in-depth information contained within the forums, let alone sourcing the correct componentry from the scattered array of part suppliers.
So let us do the hard work for you!
These boards are designed to fit into your factory ECU/DME housing, to make for a clean install using the car’s factory engine harness.
Currently, this kit can be made to suit the following BMW Motors:
M40 (E36 Era)
M42
M43
M50NV
M50TU
M60
This kit is capable of:
6-cylinder sequential injection/ignition (with firmware modification)
Launch Control
Accepts boost solenoid output
Wideband input
Flex fuel input
3 spare relay outputs
3 spare analog/digital inputs for additional sensors
To install the kit, you will need to open up the ECU in your car and remove the original circuit board and replace with this kit.
Additionally, you will need to drill/dremel out openings for the rear I/O of the ECU to cover the MAP (optional) sensor input, the 16 pin expansion plug (optional) and Arduino USB Input (mandatory)
If you are unsure or have queries about this item, please contact us before ordering.
*Extra Components included:
x1 VR Conditioner
Extras
We also offer a core exchange service at an additional charge.
You simply ship us your ECU and we will take care of the entire re-fit for you and once done, we send you back the newly fitted-out ECU, as well as the original components, ready to go!
NB: This circuit board is designed by Pazi88 and all credit goes to them.
Note: Please allow a lead time of 1-2 weeks to assemble and test these boards. Enclosures are provided while stocks last. Please let us know if you don’t require one.
For newcomers to the world of Speeduino, it can be a challenge to navigate through the in-depth information contained within the forums, let alone sourcing the correct componentry from the scattered array of part suppliers.
So let us do the hard work for you!
These boards are designed to fit into your factory ECU/DME housing, to make for a clean install using the car’s factory engine harness.
Currently, this kit can be made to suit the following BMW Motors:
M40 (E36 Era)
M42
M43
M50NV
M50TU
M60
This kit is capable of:
6-cylinder sequential injection/ignition (with firmware modification)
Launch Control
Accepts boost solenoid output
Wideband input
Flex fuel input
3 spare relay outputs
3 spare analog/digital inputs for additional sensors
To install the kit, you will need to open up the ECU in your car and remove the original circuit board and replace with this kit.
Additionally, you will need to drill/dremel out openings for the rear I/O of the ECU to cover the MAP (optional) sensor input, the 16 pin expansion plug (optional) and Arduino USB Input (mandatory)
If you are unsure or have queries about this item, please contact us before ordering.
*Extra Components included:
x1 VR Conditioner
Extras
We also offer a core exchange service at an additional charge.
You simply ship us your ECU and we will take care of the entire re-fit for you and once done, we send you back the newly fitted-out ECU, as well as the original components, ready to go!
NB: This circuit board is designed by Pazi88 and all credit goes to them.